| Author |
Message |
|
|
Post subject: 5.6.1 RC
 Posted: 18.06.2015 - 15:40 #109247
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
Hello,
vedel by please niekto vysharovat, alebo mailom poslat tuto verziu firmware pre XM?
Dik. |
|
|
| |
|
|
|
 |
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 18.06.2015 - 17:06 #109248
|
|
Majster
Joined: Jan 08, 2006
Posts: 2584
|
|
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 18.06.2015 - 17:12 #109249
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
| Jo, mam. Velmi pekne dakujem!!!!!! |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 18.06.2015 - 21:39 #109252
|
|
Basic
Joined: Feb 18, 2007
Posts: 418
|
|
Mozem sa spytat ze cim je taky vynimovny tento FW?
Edit: aha uz viem, som myslel ze to je nejaky stary FW ale to je novy RC
AirOS v5.6.1-RC Change Log:
- Fix: Device hangs on startup when DHCP relay is enabled on two LAN interfaces
- Fix: wrong reporting of airMAX Quality/Capacity (XW)
- Fix: RADIUS MAC authentication (was broken since hostapd update)
- Fix: Long Range PTP mode stops passing traffic on high load (XW)
- Fix: Sometimes AP can’t change channel after RADAR detection
- Fix: IPv6 PPPoE setup - default route isn’t set
- Fix: airGW provisioning creates wrong forward rules in case of PPPoE client configuration on WAN interface
- New: Upgrade OpenSSL to 1.0.2a
KNOWN ISSUE:
RocketM5-Ti (XW) LAN port lockup when negotiated at 1Gbps. Please make sure you are using good quality shielded LAN cables and devices are properly grounded. |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 19.06.2015 - 13:05 #109254
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
Mna skor zaujimal SNMP update. Konecne ide z AP citat CCQ, uroven sumu, AMC/AMQ pripojenych stanic....
Akurat zopar parametrov mi nie je jasnych, neviete niekto, co to moze byt?  nie som zaregistrovany ako beta-tester, tak to nechcem rozoberat na ubnt fore....
.1 - zoznam mac cpe
.2 - nazvy cpe
.3 - tx signal level
.4 - noise floor
.5 - ???
.6 - ccq
.7 - ???
.8 - amq
.9 - amc (bullet, max. 50%)
.10 - ip cpe
.11 - tx speed
.12 - rx speed
.13 - tx data transfer
.14 - rx data transfer
.15 - connection time
iso.3.6.1.4.1.41112.1.4.7.1.1
Array
(
[0] => "00 15 6D A9 55 0E "
[1] => "00 15 6D A9 C2 D4 "
[2] => "00 15 6D AB 1A AC "
[3] => "00 15 6D AD 61 1E "
[4] => "00 15 6D DC 3D 8A "
[5] => "00 15 6D DC C2 F8 "
[6] => "00 15 6D DC CB 6B "
[7] => "00 15 6D DE C2 BE "
[8] => "00 15 6D FE 78 B0 "
[9] => "00 27 22 04 B9 F3 "
[10] => "00 27 22 28 BA 00 "
[11] => "00 27 22 3C 8B D9 "
[12] => "DC 9F DB 50 8A DE "
)
1
iso.3.6.1.4.1.41112.1.4.7.1.2 (
Array
(
[0] => "ap-01"
[1] => "ap-02"
[2] => "ap-03"
[3] => "ap-04"
[4] => "ap-05"
[5] => "ap-06"
[6] => "ap-07"
[7] => "ap-08"
[8] => "ap-09"
[9] => "ap-10"
[10] => "ap-11"
[11] => "ap-12"
[12] => "ap-13"
)
1
iso.3.6.1.4.1.41112.1.4.7.1.3
Array
(
[0] => -65
[1] => -63
[2] => -61
[3] => -60
[4] => -53
[5] => -56
[6] => -61
[7] => -66
[8] => -60
[9] => -61
[10] => -63
[11] => -61
[12] => -61
)
1
iso.3.6.1.4.1.41112.1.4.7.1.4
Array
(
[0] => -85
[1] => -85
[2] => -85
[3] => -85
[4] => -85
[5] => -85
[6] => -85
[7] => -85
[8] => -85
[9] => -85
[10] => -85
[11] => -85
[12] => -85
)
1
iso.3.6.1.4.1.41112.1.4.7.1.5
Array
(
[0] => 150
[1] => 0
[2] => 300
[3] => 0
[4] => 0
[5] => 150
[6] => 0
[7] => 300
[8] => 0
[9] => 150
[10] => 0
[11] => 150
[12] => 0
)
1
iso.3.6.1.4.1.41112.1.4.7.1.6
Array
(
[0] => 99
[1] => 99
[2] => 99
[3] => 99
[4] => 99
[5] => 99
[6] => 99
[7] => 99
[8] => 98
[9] => 99
[10] => 99
[11] => 99
[12] => 99
)
1
iso.3.6.1.4.1.41112.1.4.7.1.7
Array
(
[0] => 3
[1] => 3
[2] => 3
[3] => 3
[4] => 3
[5] => 3
[6] => 3
[7] => 3
[8] => 3
[9] => 3
[10] => 3
[11] => 3
[12] => 3
)
1
iso.3.6.1.4.1.41112.1.4.7.1.8
Array
(
[0] => 86
[1] => 92
[2] => 94
[3] => 96
[4] => 94
[5] => 91
[6] => 96
[7] => 93
[8] => 86
[9] => 90
[10] => 88
[11] => 97
[12] => 90
)
1
iso.3.6.1.4.1.41112.1.4.7.1.9
Array
(
[0] => 41
[1] => 42
[2] => 43
[3] => 45
[4] => 43
[5] => 42
[6] => 45
[7] => 46
[8] => 38
[9] => 41
[10] => 37
[11] => 46
[12] => 40
)
1
iso.3.6.1.4.1.41112.1.4.7.1.10
Array
(
[0] => 192.168.1.104
[1] => 192.168.1.108
[2] => 192.168.1.101
[3] => 192.168.1.112
[4] => 192.168.1.115
[5] => 192.168.1.111
[6] => 192.168.1.102
[7] => 192.168.1.105
[8] => 192.168.1.113
[9] => 192.168.1.106
[10] => 192.168.1.110
[11] => 192.168.1.109
[12] => 192.168.1.114
)
1
iso.3.6.1.4.1.41112.1.4.7.1.11
Array
(
[0] => 48000000
[1] => 48000000
[2] => 48000000
[3] => 48000000
[4] => 48000000
[5] => 48000000
[6] => 48000000
[7] => 48000000
[8] => 48000000
[9] => 48000000
[10] => 48000000
[11] => 48000000
[12] => 48000000
)
1
iso.3.6.1.4.1.41112.1.4.7.1.12
Array
(
[0] => 54000000
[1] => 48000000
[2] => 48000000
[3] => 54000000
[4] => 48000000
[5] => 54000000
[6] => 54000000
[7] => 54000000
[8] => 48000000
[9] => 48000000
[10] => 54000000
[11] => 54000000
[12] => 6000000
)
1
iso.3.6.1.4.1.41112.1.4.7.1.13
Array
(
[0] => 24830834
[1] => 1528396502
[2] => 587804
[3] => 371001518
[4] => 2587168
[5] => 97055757
[6] => 74180979
[7] => 2158094
[8] => 1287062
[9] => 88534081
[10] => 1799790784
[11] => 1899441
[12] => 135692872
)
1
iso.3.6.1.4.1.41112.1.4.7.1.14
Array
(
[0] => 7071072
[1] => 48643218
[2] => 724329
[3] => 27873945
[4] => 3280173
[5] => 10195284
[6] => 8342061
[7] => 4361190
[8] => 2605997
[9] => 9978599
[10] => 81736922
[11] => 3127315
[12] => 9340140
)
1
iso.3.6.1.4.1.41112.1.4.7.1.15
Array
(
[0] => 0:19:19:29.00
[1] => 0:11:45:45.00
[2] => 0:11:41:44.00
[3] => 0:19:19:32.00
[4] => 0:11:45:44.00
[5] => 0:11:21:23.00
[6] => 0:10:24:45.00
[7] => 0:19:14:26.00
[8] => 0:11:30:23.00
[9] => 0:11:23:51.00
[10] => 0:11:40:15.00
[11] => 0:11:38:05.00
[12] => 0:5:42:08.00
)
1 |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 19.06.2015 - 14:11 #109255
|
|
Majster
Joined: Jan 08, 2006
Posts: 2584
|
|
.5 by mala byt vzdialenost
.7 zasa AMX Priority |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 19.06.2015 - 15:29 #109256
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
....domnienka? ci vycucane z nejakeho updatnuteho MIB?
A mohli tam uz dorobit aj latenciu, ked uz.... |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 19.06.2015 - 16:00 #109257
|
|
Majster
Joined: Jan 08, 2006
Posts: 2584
|
|
ziadna domniekna, ale fakt
Code: › UbntStaEntry ::= SEQUENCE {
ubntStaMac MacAddress,
ubntStaName DisplayString,
ubntStaSignal Integer32,
ubntStaNoiseFloor Integer32,
ubntStaDistance Integer32,
ubntStaCcq Integer32,
ubntStaAmp Integer32,
ubntStaAmq Integer32,
ubntStaAmc Integer32,
ubntStaLastIp IpAddress,
ubntStaTxRate Integer32,
ubntStaRxRate Integer32,
ubntStaTxBytes Counter64,
ubntStaRxBytes Counter64,
ubntStaConnTime TimeTicks,
ubntStaLocalCINR Integer32
} |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 19.06.2015 - 22:04 #109258
|
|
Guru
Joined: Okt 23, 2005
Posts: 1031
Location: /etc/bin/ladin
|
|
Chlapci serte na snmp aj ked konecne potesilo...
Konecne funguje jak gula nativne ipv6 cez pppoe klientom(voci CCR ).Normalne, ze zatial bezchybne presne ako ma a ako som dufal.
|
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 07.07.2015 - 08:17 #109351
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
| A je to tu!!!! Konecne release!!!! Stahujte, upgradujte |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 07.07.2015 - 14:09 #109354
|
|
Majster
Joined: Feb 14, 2011
Posts: 2544
|
|
Version 5.6.1-Service release (July 3, 2015)
-------------------------------------------------
New:
- New: Private SNMP MIB
- New: IPv6 support
- New: Manage custom scripts
- New: Extend Statistics reporting - TX/RX reporting improvement
- New: Extend Statistics reporting - Latency for each Station
- New: Statistics - ACK/Distance display
- New: Report remote TX power in AP/STA info
- New: Show RX Signal per Chain
- New: Add firmware prefix reporting for any model (TI/XM/XW)
- New: Display actual operating frequency range in MAIN page
- New: Show radio mode in Site Survey scan results
- New: DHCP address reservation
- New: Implement QOS for VLANS
- New: Increase password length to more than 8 symbols
- New: Increase MTU/MRU to 1500 bytes for PPPoE (server must support max-payload tag)
- New: airMAX devices will support only WPA-AES/WPA2-AES security (WEP optional for AP-Repeater mode)
- New: Channel shifting is removed. Frequency selection in 2MHz/5MHz steps available when in airMAX mode
- New: TCP support for remote system logging
- New: DynDNS More providers supportÂ
- New: Linux kernel update to 2.6.32.65
- New: Upgrade lighttpd 1.4.35
- New: Update hostapd/wpa_supplicant to the latest available stable version (v2.1 final)
- New: Upgrade libevent to 2.0.22
- New: Upgrade dropbear to v2014.63
- New: Upgrade OpenSSL to 1.0.2a
Fixes:
- Fix: Device hangs on startup when DHCP relay is enabled on two LAN interfaces
- Fix: Long Range PTP mode stops passing traffic on high load (XW)
- Fix: Sometimes AP can’t change channel after RADAR detection
- Fix: airGW provisioning creates wrong forward rules in case of PPPoE client configuration on WAN interface
- Fix: Broadcast goes from one STA to another STA even if Client Isolation function is enabled on AP
- Fix: Report DFS Wait or DFS Radar in MAIN page
- Fix: AP drops all stations. Recovers after reboot. (XW)
- Fix: Crash during upgrade from v5.5.x when parsing incorrect IPTABLES rules
- Fix: Update EIRP limits for Australia according channel bandwidth
- Fix: Allow 0.0.0.0 Fallback IP for PPPoE client configuration
- Fix: Various DFS and Frequency List usage improvements
- Fix: Speed test low values when using Management VLAN
- Fix: DFS improvements for Czech Republic
- Fix: airSelect can use only non-DFS frequencies
- Fix: No full-restart when changing ACL list first time after upgrade to v5.6.x
- Fix: Wrong 32 symbols SSID reporting to airControl
- Fix: Remote statistics reporting to client keeps Android phone wake up all the time
- Fix: Update EIRP limits for Brazil
- Fix: PPPoE MTU/MRU limited according to parent interface settings
- Fix: Traffic stops after Site Survey execution on remote Station when hidden SSID is set on AP
- Fix: M900 radio fails initialisation in heavy noise environment
- Fix: STA Device Name is truncated in SNMP reporting
- Fix: SNMP string sizes
- Fix: Station can't connect to AP with Hidden SSID (XW)
- Fix: Discovery response leak across VLANs
- Fix: Station shows wrong "TX Signal" in AP details window
- Fix: The same channel numbering for 4920-5000MHz and 5920-6000MHz (Compliance Test).
- Fix: Disable UPnP SSDP messages in Syslog
- Fix: Main tab is empty if device name contains <tab> symbol
- Fix: Scan results buffer size limit issue (at ~200 APs found)
- Fix: Reduce TX power to the EIRP Limit when radio is operating in Station mode or Auto frequency selection is chosen for AP
- Fix: Speedup DHCP and PPPoE clients to update IP settings after successful WPA authentication
- Fix: SSL v3 POODLE vulnerability
- Fix: Add 5GHz frequencies for Kazakhstan
- Fix: Validate ping interval for Ping Watchdog. It can’t be set to 0 sec.
- Fix: Improved Wireless page loading routine
- Fix: AirMax Capacity/Quality calculation/reporting with Fixed Rates
- Fix: TX flow control and multi queue support. (XW)
- Fix: Error after run Speed Test (XW)
- Fix: ACK/Distance miscalculation when connecting to XM AP. (HT8, HT30, XW)
- Fix: AP/STA performance issues (XW, airMax)
- Fix: HT20 Rates are reported/used when device is configured to operate in HT40 and fixed rate is selected. Alternative rate module selected
- Fix: Site Survey does report the same NF value for each channel (XW)
- Fix: Strange AirView view on Rocket M5 Titanium (XW)
- Fix: airSync does not work with fixed rates (XW)
- Fix: Radio has to fallback to full channel list if configured Frequency List is enabled but doesn't contain valid frequencies (XW)
- Fix: Remote Syslog message type is "unknown"
- Fix: Last IP isn't taken from VLAN tagged packets (XW)
- Fix: RADIUS accounting issue (XW)
- Fix: Selecting SSID on HT40 may change Channel width from 'Auto HT20/40' to 'HT20'
- Fix: Disable ACK slider if AirSync/Long range PtP selected
- Fix: Antenna alignment tool (beeper) crashes on iPhone, iMac, etc.
- Fix: Don't suggest WPA key as Username for login save (Firefox)
- Fix: Wireless page is broken (IE8/9)
- Fix: XW: Improved Data Rate selection for Default rate algorithm when operating in noisy environment
- Fix: Remove 924MHz (shifted frequency) as it’s out of allowed band range (10MHz channel width)
- Fix: Add full product name in discovery reporting
- Fix: AP crash with Multicast Enhancement enabled and specific multicast traffic on STA association
- Fix: Scan results ageing issue
- Fix: Ping tool doesn’t execute ping in 1sec interval
- Fix: Ping tool ping count is sometimes higher than defined
- Fix: Unable to set empty PPPoE password (Chrome specific)
- Fix: Proper antenna polarisation selection for 802.11abg support
- Fix: Some frequencies were missing for India when 30MHz channel width is selected
- Fix: Improved association with older devices
- Fix: Escape quotes for Device Name and SSID in Station List
- Fix: Make �Feed only -3dBi’ as default antenna selection for appropriate models
- Fix: XW: WPA2-PSK Association time out in case of long channel list
- Fix: Min TX Power for NanoBridgeM5 should be -8dBm
- Fix: Discovery returns wrong product name
- Fix: Speedtest duration validation in range [1-99]
- Fix: Reload newly uploaded configuration file
- Fix: ac-agent doesn't send GPS coordinates read from GPS module
- Fix: STA continuous crash when connecting to Apple AirPort AP
- Fix: AP doesn't initiate re-authentication to RADIUS server when Station re-associates
- Fix: EAP TTLS/PEAP do not check time in TLS session
- Fix: WEB UI: Can’t logout on high CPU load
- Fix: Discovery shows empty Device Name if length is 64 symbols
- Fix: Italian translation updates
- Fix: Spanish translation updates
- Fix: Simplified Chinese translation updates
Improvements:
- WEB UI: Disable controls while Speed Test is in progress
- WEB UI: Show explanation after move mouse on RX/TX Signal labels
- WEB UI: Ordering by frequency improvement
- WEB UI: Site Survey results sorting improvements
- WEB UI: Update “Long Range PtP Mode” help message
- WEB UI: Change EIRP Limit warning message and Auto Adjust to EIRP Limit label
- WEB UI: Increase TEST mode timeout for DFS frequencies
- WEB UI: Don’t allow to select AP with unsupported security mode in Site Survey
- WEB UI: Port forwarding from LAN side when accessing WAN IP (NAT loopback) |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 07.07.2015 - 17:14 #109355
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
- New: Channel shifting is removed. Frequency selection in 2MHz/5MHz steps available when in airMAX mode
na niektorych PtP spojoch mam zapnuty Channel Shifting. Upgradoval to uz takto niekto? Nech viem, na co sa mam pripravit, ci sa mi to potom zlinkuje... |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 07.07.2015 - 22:40 #109356
|
|
Majster
Joined: Jan 08, 2006
Posts: 2584
|
|
| Keď máš zapnutý airmax malo by sa to zlinkovať |
|
|
| |
|
|
|
|
|
|
|
Post subject: RE: 5.6.1 RC
Posted: 10.07.2015 - 09:20 #109387
|
|
Basic
Joined: Jún 19, 2006
Posts: 67
|
|
| Freq. step je po 5MHz, a Client zozuzle vsetko, takze je to OK. |
|
|
| |
|
|
|
|
|
|
Powered by PNphpBB2 © 2003-2005 The PNphpBB Group
Credits |
